Current Top Sellers
Timney Featherweight Deluxe Triggers are precision machined and hand-fitted to provide a crisp trigger pull. They feature a lightweight alloy housing with machined and hardened steel working surfaces. The trigger pull weight is adjustable from 1.5 to 4lbs. and is adjustable for creep and overtravel. Minor fitting may be required. The Featherweight Deluxe also features a trigger blocking side safety. Minor fitting may be required.
Since it was founded in 1946, Timney Triggers has built a reputation based on the quality of its products. Because of the precision machining and workmanship that goes into each Timney product they are The World's Finest Triggers.™ Each and every Timney Trigger is individually tested and calibrated by hand in the action it was designed for before it's delivered to the customer's door.
Remington 700 Adjustment Guide
1. Sear Engagement
Turn screw clockwise until it stops (hits the safety)
Back off screw until safety plunger moves freely.
Test the safety to make sure it moves back and forth smoothly.
Re-engage the safety and make sure the trigger doesn’t have excessive movement with the safety in the safe position.
2. Overtravel After you adjust your sear engagement dry fire the rifle. Without cocking tighten the over travel screw in until it hits the trigger and then back it out about 1/6 of a turn or one flat of the hex wrench. It should move freely and fire easily but you shouldn’t have to “chase” the trigger more than about .015
3. Pull weight It’s important that you NOT take the pull weight too low; it must maintain spring pressure or will Bump / slam fire. When you pull the trigger, with the bolt open, the trigger’s spring should return it to the neutral position; if it doesn’t you don’t have enough spring pressure. To adjust spring pressure turn the screw in (Clockwise) until you can feel the pressure of the spring on the actual trigger lever. Close the bolt and dry fire the rifle. We recommend using a trigger pull gauge in the center of the trigger to measure the pull weight. If you don’t have one you need to get one, they aren’t very expensive, we sell them for around $35.00 It must be between 1.5 and 4lbs to function correctly. From there you take the screw in or out to measure the feel (weight) of the trigger.
Once you have it set where you like it rapid dry fire to ensure it functions perfectly. Test for slam fires by closing the bolt harder, don’t get insane but do shut it hard and with more force than normal. You are testing for accidental or unintentional discharge, if you were hunting and had to rapidly reload and do a second shot it shouldn’t discharge unintentionally.
When you reassemble, be sure to use a flashlight to look into the trigger well, the trigger should not rub or make contact with the trigger well or the trigger guard. It should, in theory, float through without contact, close is good, however rubbing is bad. With the rifle in the cocked position and the safety engaged drop the rifle 12 inches, but first, onto a padded floor to test for drop fire. It should not fire with the safety on and shouldn’t dent a primer either.
Tech Guide Downloads
This trigger works with these rifles:
- All 700 Actioned clones
- Christensen Arms Carbon One
- Defiance Machine 700 Action
- Les Bear Tactical Bolt Action
- Model 673
- Model 700 200th Ann. LTD. ED.
- Model 700 5-R Series Gen 2
- Model 700 ADL 200th Ann CE
- Model 700 American Wilderness Rifle
- Model 700 BDL
- Model 700 CDL
- Model 700 CDL SF
- Model 700 Long Range
- Model 700 Magpul
- Model 700 Mountain Stainless Steel
- Model 700 Sendero SF II
- Model 700 SPS
- Model 700 SPS Camo
- Model 700 SPS Compact
- Model 700 SPS Stainless
- Model 700 SPS Tactical
- Model 700 SPS Tactical AAC-SD
- Model 700 SPS Threaded Barrel
- Model 700 SPS Varmint
- Model 700 Stainless 5-R Mil - Spec
- Model 700 Stainless 5-R Threaded Barrel
- Model 700 Tactical Chassis
- Model 700 Varmint SF
- Model 700 VLS
- Model 700 VTR
- Model 700 VTR Stainless Steel
- Model 700 XCR Compact Tactical
- Model 700 XCR Tactical
- Model 721
- Model 722
- Model 725
- Nesika Tactical Action
- Remington XP-100R
- Sendero Reminton M722
What Is Trigger Pull weight?
Pull weight is the amount of pressure, in ounces or pounds, required to fire the trigger. Or in other words, how hard you have to squeeze the trigger to shoot your rifle. Timney Trigger experts at our Phoenix, Arizona plant hand-test every trigger in its intended action and then set the pull weight at our factory standard, 3 lbs.
If you prefer a different pull weight you simply select it from the drop down above and your Timney Trigger will be customized to your preference.
The #1 reason to replace your factory trigger with a Timney is accuracy. A lighter, crisper, more consistent trigger pull will make you more accurate with your firearm.
Below is a guide for pull weight selection:
Light trigger pull weights are great for people shooting lighter weight rifles as they can help keep you on target during the shot. Also common weights for target shooting from a bench.
By far the most common trigger pull weights -this is great for virtually all applications including target shooting, hunting and 3-gun competitions.
Heavy trigger pull weights are good for cold weather hunting or applications where you may be shooting with gloves on.