Description
Mounting Hardware is Included
This mount fits (including but not limited to):
Sig #8 Sights
P210A Standard
P220
P224
P225
P225-A1
P226
P227
P228
P229
P238
P239
P245
P320
P938
SP2022
M11-A1
MK25
Bersa Thunder UC Series (9/40/45)
Bersa Thunder HC Series (9/40/45)
FN 509
This mount does not fit:
Sig 1911s
Sig P220 10mm Hunter
Any Optics Ready Sigs i.e. P226 Legion RX, P229 RX, P320 X-Carry etc.
P210 Target
P365 (The dovetail cut is too deep to work with our mount)
FN 509 Tactical
Please note: Trijicon recommends the use of a sealing plate to prevent water from entering their red dots.
Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.780"
Overall Width: 1.1"
Mounting Hardware: (2) 6-32 Flat Head Screws, (1) 6-32 X 3/16 Set Screw
Red Dot Fitment: Trijicon RMR / SRO, Holosun HE407C / HE407C X2 / HE507C / HE507C X2 / HS407C / HS407C X2 / HS507C / HS507C X2, Swampfox Kingslayer / Liberty / Justice
Our red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.
This mount does not work on any optics ready Sigs. This red dot rear sight dovetail mount is easy to install and allows you to mount a red dot on your pistol without having to permanently modify the slide.
This mount does not work on any optics ready Sigs.
This mount fits (including but not limited to):
Sig Sauer P210A Standard
Sig Sauer P220
Sig Sauer P224
Sig Sauer P225
Sig Sauer P225-A1
Sig Sauer P226
Sig Sauer P227
Sig Sauer P228
Sig Sauer P229
Sig Sauer P238
Sig Sauer P239
Sig Sauer P245
Sig Sauer P320
Sig Sauer P938
Sig Sauer SP2022
Sig Sauer M11-A1
Sig Sauer MK25
Bersa Thunder UC Series (9/40/45)
Bersa Thunder HC Series (9/40/45)
FN 509
Sig Sauer #8 Sight Cuts
This mount does not fit:
Sig Sauer 1911s
Sig Sauer P220 10mm Hunter
Any Optics Ready Sig Sauer i.e. P226 Legion RX, P229 RX, P320 X-Carry etc.
Sig Sauer P210 Target
Sig Sauer P365 (The dovetail cut is too deep to work with our mount)
FN 509 Tactical
Our red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.
Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.
Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs
2 Flat Head Cap Screws - Provided for Trijicon RMR
The screws that are included with this mount require a 5/64'' allen wrench for installation.
Warning: This product may be alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. To prevent exposure, do not alter the product by welding, grinding, etc. For more information, go to www.P65Warnings.ca.gov.
GTIN 841370116553
Scope Mount Color Black Hardcoat Anodized Type III
Model 509, Sig #8 Rear Sight (P210 Standard, P220, P224, P225, P225-A1, P226, P227, P228, P229, P238, P239, P245, P320 (Not Optics Ready), P938, M11-A1, MK25), Thunder UC, Thunder HC
Firearm Brand Bersa, FNH, Sig Sauer
Red Dot Brand Holosun 407C / 507C / 508T, Swampfox Kingslayer / Liberty / Justice, Trijicon RMR / SRO
