EGW VORTEX VIPER / VENOM (FITS BURRIS FASTFIRE AND DOCTER) RED DOT ADAPTER PLATE FOR SIG SAUER M17 / M18 OPTICS READY

This mount fits:
Sig M17 (with Romeo1 PRO cut)
Sig M18 (with Romeo1 PRO cut)
Sig P320 X-Five Legion (with Romeo1 PRO cut)
Sig P320 X-Carry Optics Ready (with Romeo1 PRO cut and no rear sight cut)
Sig P320 X-Compact (with Romeo1 PRO cut and no rear sight cut)

This mount does not fit:
Any Sig P320 models with dovetail cut for rear sight
Sig P320 RX
Sig P320 RX X-Compact
Sig P320 X-Five (with Romeo1 cut)
Sig M17 Military Surplus

We have found that minor fitting may be required to the rear step of the adapter plate due to slightly undersized cuts on Sig's slides. This can easily be done by filing on the rear step until the mount fits in the cut.

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.775"
Overall Width: .99"
Torque Specs: 15 in/lbs

Mounting Hardware:
(2) 6-32 x 5/16" Button Head Screws - Requires 5/64 Wrench or Driver
(2) 6-32 x 3/8" Flat Head Screws - Requires 5/64 Wrench or Driver
(2) 4-40 x 1/4" Socket Cap Head Screws - Requires 3/32 Wrench or Driver

Red Dot Fitment:
Vortex Viper
Vortex Venom
Burris Fast Fire 1, 2, 3, 4
Docter
ADE RD3-001
ADE RD3-002
ADE RD3-009
UTG Reflex Micro Dot
Crimson Trace CTS-1200
Crimson Trace CTS-1300
Sightmark Mini Shot
Sightmark Core Shot

*All ADE mounts require 6-32 x 3/8" screws.

Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.

Our EGW red dot sight adapter plate for the Sig Sauer M17 and M18 allows you to mount a Vortex Viper, Vortex Venom, Burris Fastfire or other Docter footprint red dot sight to your Sig Sauer M17 and M18 with the Romeo1Pro factory cut slide. Please confirm your model before purchasing.

The rear sight plate on your gun needs to be removed to install your red dot on this plate. The plate is mounted to the slide from underneath the slide using the provided 4-40 screws. The red dot is then installed on top of the adapter plate using the provided 6-32 screws.

This Optics Mounting Plate Fits the Following Pistols:
Sig Sauer M17 (with Romeo1 PRO cut)
Sig Sauer M18 (with Romeo1 PRO cut)
Sig Sauer P320 X-Five Legion (with Romeo1 PRO cut)
Sig Sauer P320 X-Carry Optics Ready (with Romeo1 PRO cut and no rear sight cut)
Sig Sauer P320 X-Compact (with Romeo1 PRO cut and no rear sight cut)

This Optics Mounting Plate Does Not Fit the Following:
Any Sig Sauer P320 models with dovetail cut for rear sight
Sig Sauer P320 RX
Sig Sauer P320 RX X-Compact
Sig Sauer P320 X-Five (with Romeo1 cut)
Sig Sauer M17 Military Surplus

This Optics Mounting Plate Fits the Following Red Dots:
Vortex Viper
Vortex Venom
Burris Fast Fire 1, 2, 3, 4
Docter
ADE RD3-001
ADE RD3-002
ADE RD3-009
UTG Reflex Micro Dot
Crimson Trace CTS-1200
Crimson Trace CTS-1300
Sightmark Mini Shot
Sightmark Core Shot

Installation Instructions
- Remove the optics plate from your slide
- Install the EGW adapter plate
- Place the red dot sight on the EGW red dot adapter plate
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.