Description
Mounting hardware is included.
This mount fits:
All HK VP9 Optics Ready Models
HK VP9 Optics Ready
HK VP9L Optics Ready
HK VP9 Tactical Optics Ready
If your gun has a cut out for the optics plate, this plate will work with your application.
(This mount is comparable to the HK VP9 Optics Ready #5 Plate)
The screws that come with your slide to mount the plate to the slide may be reused. They are also available for purchase from the drop down above. HK recommends replacing the plate mounting screws after 2,000 rounds. HK recommends torquing the screws for the plate to 2Nm or 17.7 in/lbs.
The screws to mount the red dot to the plate are provided at no extra cost. We recommend using 15 in/lbs.
Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.921"
Overall Width: .99"
Torque Specs: 15 in/lbs
Mounting Hardware:
(2) 6-32 Button Head Screws - Requires 5/64 Wrench or Driver
(2) 6-32 Flat Head Screws - Requires 5/64 Wrench or Driver
Red Dot Fitment:
Vortex Viper
Vortex Venom
Burris Fast Fire 1, 2, 3, 4
Docter
ADE RD3-001
ADE RD3-002
ADE RD3-009
UTG Reflex Micro Dot
Crimson Trace CTS-1200
Crimson Trace CTS-1300
Sightmark Mini Shot
Sightmark Core Shot
*All ADE mounts require 6-32 x 3/8" screws.
Please note: We have found that some red dots commonly found on Amazon such as the UTG and ADE may not hold the same tolerances as the red dots that this mount was initially created to work with. These dots may not fit properly on the posts on the plate. We would recommend either sending the red dot back for an exchange to whichever seller you purchased it from, or open up the holes in the bottom of the red dot to accommodate the pins.
The EGW red dot sight mount adapter plates for the HK VP9 Optics Ready Models are meant to be installed in the factory slide cut. Simply remove the plate cover and replace it with our mount in order to mount your Vortex Viper, Vortex Venom, Burris FastFire, or Docter red dot sight to your HK VP9 Optics Ready, HK VP9L Optics Ready, HK VP9 Tactical Optics Ready or any other HK VP9 Optics Ready Models. You can take our mount off and replace your rear sight at any time. Mounting hardware included.
Installation Instructions
- Remove the rear cover plate
- Install the EGW sight mount and torque the mounting plate screws
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque red dot mounting screws to 15in/lbs
2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights
The screws that are included with this mount require a 5/64'' allen wrench for installation.
Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Warning: This product may be alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. To prevent exposure, do not alter the product by welding, grinding, etc. For more information, go to www.P65Warnings.ca.gov.
More Information
GTIN - 841370118199
Scope Mount Color - Black Hardcoat Anodized Type III
Model - VP9 | VP9L Optics Ready
Firearm Brand - HK (Heckler & Koch)
Red Dot Brand - ADE RD3-001 / RD3-002 / RD3-006 / RD3-009 / RD3-012 / RD3-013 / RD3-015, Burris FastFire 1, 2, 3, 4, Crimson Trace CTS-1200 / CTS-1300, Docter, Vortex Venom / Viper
